Extracts (Powdered Extracts, PE)

From GandG.cloud
Jump to navigation Jump to search
Ingredient
Extracts (Powdered Extracts, PE)
G&G Cloud staff reference · last edited 5/11/2026

Many botanicals are used in their native form, just dried and powdered, e.g. Dandelion root powder or Dandelion leaf powder. Sometimes a more concentrated form is required, so we use Powdered Extracts (PE).

Extracts can be liquids, oils, resins or dry powders. G&G only uses dry powders, as they are easy to weigh accurately, store well and can be filled into capsules, tablets and powder blends.

What is a plant extract?

An extract is made by soaking plant material in a liquid (the solvent) so that the useful, soluble compounds dissolve out of it. The leftover plant fibre is thrown away and the liquid is dried down to a powder. The result is a concentrate that contains much more of the plant's active compounds, weight for weight, than the plain dried herb.

The part of the plant matters as much as the species. For example, Turmeric extract comes from the root (rhizome), Ginkgo from the leaf and Milk Thistle from the seed. Always check that the plant part on the specification matches what we want to claim on the label.

How an extract is made

  1. Harvest and identity check – the supplier confirms it is the correct plant and plant part.
  2. Drying and milling – the plant is dried and ground so the solvent can reach the compounds.
  3. Extraction – the ground plant is mixed with a solvent, most often water, ethanol (alcohol), a water/ethanol mix, or carbon dioxide under pressure (supercritical CO₂).
  4. Filtering – the spent plant material is separated from the liquid.
  5. Concentrating – most of the solvent is removed, usually by gentle evaporation under vacuum to protect heat-sensitive compounds.
  6. Drying – the concentrate is turned into a powder, usually by spray drying. A carrier such as maltodextrin, gum arabic or microcrystalline cellulose is often added so the powder doesn't turn sticky.
  7. Milling and testing – the powder is sieved to size and tested.

The solvent changes what ends up in the extract. Water pulls out different compounds from alcohol, and CO₂ is mainly used for oily compounds. Two extracts of the same plant can therefore be quite different, even if they look the same on paper.

The two main types

Extracts are sold in two ways: as a ratio extract or as a standardised extract.

Ratio extract (e.g. 4:1, 10:1, 20:1) Standardised extract (e.g. 95% curcuminoids)
What it means The amount of dried plant used to make the extract. 10:1 means 10 kg of dried herb was used to make 1 kg of extract. The extract is tested and adjusted to contain a set percentage of a key ("marker") compound.
Label claim "Whole herb equivalent", e.g. 100 mg of a 10:1 extract = 1,000 mg of dried herb. The amount of the active compound, e.g. 500 mg Turmeric extract providing 475 mg curcuminoids.
Benefits Usually cheaper. Keeps the full range of the plant's compounds. Allows high "equivalent" figures. Tested, so the active level is the same in every batch, regardless of harvest or growing region.
Drawbacks Actives are not usually tested, so we cannot claim an active content. The ratio says nothing about how it was made. Usually more expensive. Often branded/trademarked, sometimes with restrictive licence agreements (although generic versions exist).

A higher ratio is not always "stronger"

A big number like 100:1 looks impressive, but only the soluble part of a plant can be extracted. After a point, there is nothing left to concentrate. A ratio also doesn't show the solvent or method used, so two 10:1 extracts of the same plant can differ. A well-documented 4:1 extract may tell you more than a vague 100:1.

Claiming both ratio and standardisation

Customers sometimes want both on the label. This causes problems:

  • A standardised extract can be worked out as a ratio, but because crops vary, the ratio changes from batch to batch. Suppliers often give a range (e.g. 8–9:1), which makes an exact label claim difficult.
  • A ratio extract is not tested for actives, so if asked "what % active is in it?", the honest answer is that we don't know, and it would vary each batch anyway.

Best practice

Decide what the product needs to claim, then choose one type:

  • Ratio extract – to claim a whole herb equivalent, e.g. "300 mg of 10:1 extract, equivalent to 3,000 mg of dried herb".
  • Standardised extract – to claim an active compound, e.g. "300 mg Turmeric extract standardised to 95% curcuminoids".

Avoid declaring both, as one of the figures will usually be wrong.

What to check on a supplier specification

  • Latin name and plant part used
  • Ratio (DER) or standardisation level, and the test method (usually HPLC)
  • Extraction solvent
  • Carrier used and how much
  • Moisture (usually 5% or less) and particle size/mesh
  • Contaminant testing: heavy metals, pesticides, solvent residues, PAHs and microbiology

Regulatory points

  • Health claims – there are no authorised health claims for plant extracts as such. Only use claims on the GB Nutrition and Health Claims Register; check with the Technical team first.
  • Novel Food – an extract can be a Novel Food even when the plain herb is not, because the plant part and the way it is extracted both count. Check before using a new extract.
  • Solvents – only permitted extraction solvents may be used for food (Directive 2009/32/EC, retained in GB law).

Further information

The original G&G information sheet:

Media:Botanical Extracts.pdf

References

  1. G&G Information Sheet – Botanical Extracts: Standardised vs Ratio (linked above)
  2. Plants2Market – How Is a Plant Extract Made?: https://www.plants2market.com/en/blog/news-4/plant-extracts-292